Issue
We have a master-slave replication configuration as follows.
On the master:
postgresql.conf
has replication configured as follows (commented line taken out for brevity):
max_wal_senders = 1
wal_keep_segments = 8
On the slave:
Same postgresql.conf
as on the master. recovery.conf
looks like this:
standby_mode = 'on'
primary_conninfo = 'host=master1 port=5432 user=replication password=replication'
trigger_file = '/tmp/postgresql.trigger.5432'
When this was initially setup, we performed some simple tests and confirmed the replication was working. However, when we did the initial data load, only some of the data made it to the slave.
Slave's log is now filled with messages that look like this:
< 2015-01-23 23:59:47.241 EST >LOG: started streaming WAL from primary at F/52000000 on timeline 1
< 2015-01-23 23:59:47.241 EST >FATAL: could not receive data from WAL stream: ERROR: requested WAL segment 000000010000000F00000052 has already been removed
< 2015-01-23 23:59:52.259 EST >LOG: started streaming WAL from primary at F/52000000 on timeline 1
< 2015-01-23 23:59:52.260 EST >FATAL: could not receive data from WAL stream: ERROR: requested WAL segment 000000010000000F00000052 has already been removed
< 2015-01-23 23:59:57.270 EST >LOG: started streaming WAL from primary at F/52000000 on timeline 1
< 2015-01-23 23:59:57.270 EST >FATAL: could not receive data from WAL stream: ERROR: requested WAL segment 000000010000000F00000052 has already been removed
After some analysis and help on the #postgresql IRC channel, I've come to the conclusion that the slave cannot keep up with the master. My proposed solution is as follows.
On the master:
- Set
max_wal_senders=5
- Set
wal_keep_segments=4000
. Yes I know it is very high, but I'd like to monitor the situation and see what happens. I have room on the master.
On the slave:
- Save configuration files in the data directory (i.e.
pg_hba.conf pg_ident.conf postgresql.conf recovery.conf
) - Clear out the data directory (
rm -rf /var/lib/pgsql/9.3/data/*
) . This seems to be required bypg_basebackup
. - Run the following command:
pg_basebackup -h master -D /var/lib/pgsql/9.3/data --username=replication --password
Am I missing anything ? Is there a better way to bring the slave up-to-date w/o having to reload all the data ?
Any help is greatly appreciated.
Solution
The two important options for dealing with the WAL for streaming replication:
wal_keep_segments
should be set high enough to allow a slave to catch up after a reasonable lag (e.g. high update volume, slave being offline, etc...).archive_mode
enables WAL archiving which can be used to recover files older thanwal_keep_segments
provides. The slave servers simply need a method to retrieve the WAL segments. NFS is the simplest method, but anything from scp to http to tapes will work so long as it can be scripted.# on master archive_mode = on archive_command = 'cp %p /path_to/archive/%f' # on slave restore_command = 'cp /path_to/archive/%f "%p"'
When the slave can't pull the WAL segment directly from the master, it will attempt to use the
restore_command
to load it. You can configure the slave to automatically remove segments using thearchive_cleanup_command
setting.
If the slave comes to a situation where the next WAL segment it needs is missing from both the master and the archive, there will be no way to consistently recover the database. The only reasonable option then is to scrub the server and start again from a fresh pg_basebackup
.
Answered By - Ben Grimm